About

 

 

Each person may have their own unique assumption when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, as well as in some cases, tiling skills. Changing an old tub with a new one is also a reasonably tough job. If the old tub is conveniently easily accessible, the job can move speedily; if you need to open a wall surface to get rid of the old tub and place the brand-new bathtub, the job is a lot harder. In either case, the project is within a residence handyman's skills, although you will require a helper to move out the old bathtub as well as set in the brand-new one. Ensure you have actually certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to think about using one prior to you start. Possibilities are you might need a professional plumber to make tube links.
This short article will certainly assist you mount a new bathtub in your shower room if you have currently purchased a brand-new tub as well as do not need to transform the arrangement of your previous water pipes.
Your devices and also material list should consist of the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing taps can be fairly problematic as a result of the restricted accessibility that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipes to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before carrying on to fit the new faucets, contrast the pipe connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.

 

 

Suitable New Touches

If the tails of the new taps are plastic, after that you will certainly need a plastic port to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines remain in area in between the faucet and the sink. Secure the tap in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular tap connectors. The former type ought to be linked to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Installing the Bath tub

Using the two wooden boards under its feet, place the bathtub in the required position. The wooden boards are helpful in evenly spreading the weight of the bathtub over the area of the boards instead of focusing all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by examining the level and also readjusting the feet on the bath tub up until the level checks out level.
To install taps, fit the bottom of the outermost adaptable faucet port to the proper supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water system as well as check all joints and brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub as well as additionally inspect the overflow outlet and the normal electrical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also sealing around the bath tub should wait till the tub has actually been made use of at least when as this will settle it right into its last placement.

 

 

Planning for the Installation

To start with, the supporting frame provided with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted in between the bath and also the taps. On a plastic bath, it is likewise sensible to fit a sustaining plate under the taps unit to avoid strain on the bath tub.
Fit the versatile faucet ports to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet through the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. See to it you use every one of the supplied washing machines.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final setting.

 

 

Tiling Around the Bath tub

In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the installation can move enough to split a rigid seal, triggering the water to pass through the wall surface between the bath and also the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to blend in your components and also installations. They are marketed in tubes and cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to permit the movement experienced when the tub is in usage. The sealer can split rather very early if you do not think about this activity prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise quickly offered on the market. It is recommended to fit the ceramic tiles using water-resistant or waterproof glue and also cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I discovered that blog post on A Step-by-Step Guide to Installing a Bathtub when doing a search on the search engines. Are you aware of another individual who is looking into the niche? Feel free to promote it. Thanks so much for going through it.

Instant Quote

Request An Appointment

 

 

Everybody has got his or her own ideas on the subject of Why Your Water Pipes Are Noisy and How To Shut Them Up.

To diagnose noisy plumbing, it is necessary to determine first whether the undesirable audios occur on the system's inlet side-in other words, when water is transformed on-or on the drainpipe side. Sounds on the inlet side have varied reasons: excessive water stress, used shutoff and also tap components, poorly connected pumps or other appliances, incorrectly placed pipe fasteners, and also plumbing runs containing too many limited bends or various other restrictions. Noises on the drain side normally come from bad area or, similar to some inlet side sound, a format having limited bends.

 

Hissing

Hissing sound that happens when a tap is opened somewhat normally signals extreme water pressure. Consult your local water company if you suspect this problem; it will be able to inform you the water stress in your area as well as can mount a pressurereducing valve on the incoming water pipe if needed.

 

Various Other Inlet Side Noises

Squeaking, squeaking, damaging, breaking, as well as touching normally are triggered by the growth or tightening of pipelines, normally copper ones providing hot water. The audios take place as the pipelines slide versus loose fasteners or strike nearby home framing. You can typically identify the place of the issue if the pipes are exposed; just adhere to the audio when the pipelines are making sounds. Probably you will uncover a loosened pipeline hanger or an area where pipes exist so near flooring joists or various other framing pieces that they clatter versus them. Affixing foam pipeline insulation around the pipes at the point of contact should treat the trouble. Make sure straps and wall mounts are safe and secure as well as offer adequate assistance. Where feasible, pipe fasteners need to be connected to enormous structural components such as structure walls as opposed to to framing; doing so reduces the transmission of resonances from plumbing to surface areas that can enhance and move them. If attaching bolts to framing is inescapable, wrap pipelines with insulation or other resistant material where they speak to fasteners, and also sandwich the ends of brand-new fasteners in between rubber washers when mounting them.
Correcting plumbing runs that suffer from flow-restricting limited or numerous bends is a last hope that ought to be taken on only after getting in touch with an experienced plumbing specialist. However, this circumstance is rather common in older homes that might not have been constructed with indoor plumbing or that have seen numerous remodels, especially by novices.

 

Babbling or Shrilling

Intense chattering or shrilling that happens when a shutoff or faucet is activated, and that normally disappears when the installation is opened totally, signals loose or malfunctioning internal components. The solution is to change the shutoff or faucet with a brand-new one.
Pumps and home appliances such as cleaning devices and also dishwashers can move electric motor noise to pipelines if they are improperly linked. Connect such items to plumbing with plastic or rubber hoses-never stiff pipe-to isolate them.

 

Drain Noise

On the drain side of plumbing, the principal goals are to get rid of surface areas that can be struck by dropping or rushing water and to protect pipelines to have unavoidable sounds.
In new building, bath tubs, shower stalls, commodes, and also wallmounted sinks and basins must be set on or versus resistant underlayments to lower the transmission of noise via them. Water-saving commodes and also faucets are less noisy than conventional designs; install them rather than older kinds even if codes in your location still allow making use of older components.
Drains that do not run up and down to the cellar or that branch into straight pipe runs sustained at flooring joists or various other mounting present particularly troublesome sound troubles. Such pipes are large sufficient to emit substantial resonance; they also carry significant amounts of water, which makes the circumstance worse. In brand-new building, define cast-iron dirt pipelines (the huge pipelines that drain pipes commodes) if you can manage them. Their enormity contains a lot of the noise made by water passing through them. Also, avoid directing drains in wall surfaces shown bed rooms as well as spaces where people gather. Walls containing drains need to be soundproofed as was explained earlier, using double panels of sound-insulating fiber board and also wallboard. Pipes themselves can be wrapped with special fiberglass insulation created the objective; such pipelines have an invulnerable vinyl skin (sometimes having lead). Results are not always satisfactory.

 

Thudding

Thudding sound, typically accompanied by shuddering pipelines, when a faucet or appliance shutoff is switched off is a condition called water hammer. The noise and also resonance are caused by the resounding wave of stress in the water, which all of a sudden has no place to go. Occasionally opening a valve that releases water swiftly into an area of piping consisting of a restriction, joint, or tee installation can produce the very same condition.
Water hammer can usually be healed by installing installations called air chambers or shock absorbers in the plumbing to which the issue valves or taps are connected. These tools enable the shock wave created by the halted circulation of water to dissipate in the air they consist of, which (unlike water) is compressible.
Older plumbing systems may have brief vertical areas of capped pipe behind wall surfaces on faucet competes the exact same purpose; these can ultimately fill with water, minimizing or destroying their efficiency. The cure is to drain pipes the water system totally by shutting off the primary water supply shutoff and also opening all taps. Then open up the primary supply valve and also close the taps one by one, beginning with the faucet nearest the shutoff as well as ending with the one farthest away.

 

3 Most Common Reasons for Noisy Water Pipes

 

Water hammer

 

When water is running and is then suddenly turned off, the rushing liquid has no place to go and slams against the shut-off valve. The loud, thudding sound that follows is known as a water hammer. Besides being alarming, water hammer can potentially damage joints and connections in the water pipe itself. There are two primary methods of addressing this issue.

 

• Check your air chamber. An air chamber is essentially a vertical pipe located near your faucet, often in the wall cavity that holds the plumbing connected to your sink or tub. The chamber is filled with air that compresses and absorbs the shock of the fast moving water when it suddenly stops. Unfortunately, over time air chambers tend to fill with water and lose their effectiveness. To replenish the air chambers in your house you can do the following.


 
• Turn off the water supply to your house at the main supply (or street level).


 
• Open your faucets to drain all of the water from your plumbing system.


 
• Turn the water back on. The incoming water will flush the air out of the pipes but not out of the vertical air chamber, where the air supply has been restored.


 

Copper pipes

 

Copper pipes tend to expand as hot water passes through and transfers some of its heat to them. (Copper is both malleable and ductile.) In tight quarters, copper hot-water lines can expand and then noisily rub against your home's hidden structural features — studs, joists, support brackets, etc. — as it contracts.

One possible solution to this problem is to slightly lower the temperature setting on your hot water heater. In all but the most extreme cases, expanding and contracting copper pipes will not spring a leak. Unless you’re remodeling, there's no reason to remove sheetrock and insert foam padding around your copper pipes.

 

Water pressure that’s too high

 

If your water pressure is too high, it can also cause noisy water pipes. Worse, high water pressure can damage water-supplied appliances, such as your washing machine and dishwasher.

Most modern homes are equipped with a pressure regulator that's mounted where the water supply enters the house. If your home lacks a regulator, consider having one professionally installed. Finally, remember that most plumbers recommend that water is delivered throughout your home at no lower than 40 and no greater than 80 psi (pounds per square inch).

Whatever the state of your plumbing, one thing is certain — you’re eventually going to encounter repair and replacement issues around your home that require professional help. That’s where American Home Shield can come to your aid.

https://www.ahs.com/home-matters/repair-maintenance/causes-of-noisy-water-pipes/

 

Hopefully you enjoyed reading our topic on Why is My Home Making Strange Plumbing Noises. Thanks a lot for taking the time to read through our short article. Sharing is caring. Who knows, you may just be helping someone out. We take joy in reading our article about Why Your Water Pipes Are Noisy and How To Shut Them Up.

Book A Free Estimate